Riverside DesignJet Plotter Repair & Services in Riverside, CA

• Carriage belt replacement
• Broken carriage belt
• Print-head error
• Ink supply error
• Paper not cutting
• Noise
• Error code
• No power faulty power supply

Same-day onsite HP designjet repair includes inspectin, cleaning, lubricating and print head calibration

• Clean plotter Carriage Rails.
• Lubricate the plotter Carriage Rails.
• Cleaning the Drive Roller.
• Encoder Strip Cleaning and inspection.
• Inspect and Clean Platen Assembly.
• Clean the complete Hewlett Packard LaserJet.
• Adjust the designjet print head after exchanging the belt.
• Quality test printout.

HP 500 - 800 DesignJet Error Codes

• Error Code 86:01 – Worn Carriage belt (24″ Belt / 42″ Belt). Belt starts to breakup leaving belt dust inside printer and making clunking noise from motor with build up of rubber on gear.
• Error Code 86:01 – Dirty Encoder strip hard to clean replace. (24″ Encoder / 42″ Encoder)
• Error Code 11:11 – Trailing Cable badly connected or worn. (24″ Trailing Cbale / 42″ Trailing Cable)
• Error Code 21:10 – Service Station failure.
• Error Code 81:01 – Paper feed motor failure.
• Error Code 02:10, 02:13, 12:11 – Carriage Assembly failure.
• Error Code 03:10 – Power Supply failure.
• Error Code 05:10 – (Only applicable to HP DesignJet 800 Series) Formatter failure.
• Blue handle breaking (Pinch-Arm Mechanism)
• Some random errors can be caused by faulty printhead /ink cartridge. Take all consumables out, then switch printer back on.

HP Designjet Z6100 Error Codes

• Error 24:10, Ink broken bag error, if ink has leaked over Tube System pcb you need to replace Tube System as this can be result from 24:10. 42″ tube System – 60″ Tube System
• Error 86:01 same as 87:01 Encoder strip (42″ Encoder 60″ Encoder) getting dirty! Encoder Strip becomes unreadable after user cleaning to many times and needs replacing. Other issues from this error code Carriage Belt worn (42″ Belt 60″ Belt) and Carriage Lubrication Felt dry and dirty.
• Blank display due to CPU fan failure and printer switching off after short time.
• Ink vapors build up due to service station vent holes blocking up.
• Vacuum path holes blocked up due to ink in the holes causes reduction in holding media down.
• Media Blue Handle breaking causing handle to be loose and not releasing pinch rollers.
• Spindle (42″ Spindle 60″ Spindle) end breaking on edge causing judder on spindle plus media going out of line on long print runs.
• Roll housing right hand side tension spring breaking causing paper loading problems.
• Image quality issues: Run Image Quality Test to show which printhead is not 100%. Select the ink icon and then select Image Quality Maintenance > Printhead Diagnostics Image.
• Pinch roller assy: some of the rollers fall off then metal spring digs into feed roller.

HP Designjet 5000/5500 Error Codes

• Calibration failure at 30% or 70% line sensor failure. 5000 Line Sensor – 5500 Line Sensor
• Printer path 2! Carriage Belt worn. 42″ Belt – 60″ Belt
• Printhead failing after 40ml due to air in Tube System
• Belt Tensioner Roller broken
• Boot-up failure due to hard drive being corrupt
• Jetdirect card fail due to spike in network
• Blue End caps broken on spindle. Spindle 42″ – Spindle 60″
• Ink cartridge fail in one colour due to tube system issues
• Pinch roll assy: Some of the rollers fall off then metal spring digs into feed roller.
• Cutter roller worn or broken causing cutter not to cut media.

HP Designjet T/Z-Series Error Code

• Error Code 47:01 – Star Wheel bail arm was not moving up or down due to star wheel Motor
• Error Code 41:01 – Electrical fault or current limit in Media-Axis Motor due to paper jam or 47:01 Error code
• Error Code 03:10 – Noise coming from L/H side of printer with error – Need Power Supply.
• Error Code 86:01 – Encoder strip (24″ Encoder” 44″ Encoder) dirty need cleaning or replacing.
• Error Code 86:01 – Scan-Axis Motor failure (likely due to obstacles in the scan axis or electrical fault). Carriage belt (24″ Belt 44″ Belt) worn or Scan Axis motor faulty.
• Error Code 08:11 – No communication between the Front Panel and the Main PCA.
• Not Cutting – Cutter needs cleaning.
• Error Code 21:13 – Fail moving Service Station
• Error Code 11:01 – Trailing cable issues (24″ Trailing Cable 44″ Trailing Cable)